Kod EPBL_a248 zgłosił w aucie sterownik „Hamulec postojowy — lewy”. Litera „a” w środku kodu zalicza go do wpisów typu alert.
Lewy zacisk elektrycznego hamulca postojowego. Znaczenie kodów odpowiada grupie EPB.
Najczęstszy typ. Auto zapisało zdarzenie i mogło je pokazać na ekranie. Skala jest szeroka — od drobiazgu, który znika sam, po sprawę wymagającą naprawy.
Tak błąd nazywa się bezpośrednio w firmware auta. Przy kodach bez opisu to najdokładniejsza istniejąca wskazówka — sama nazwa mówi, czego dotyczy zdarzenie.
Poniższy tekst pochodzi z dokumentacji technicznej Tesli i zostawiamy go w oryginalnym angielskim brzmieniu, żeby tłumaczenie nie zmieniło znaczenia.
Electronic Parking Brake apply was interrupted during dynamic apply. Apply failed.
Electronic Parking Brake faulted while applying and during ESM_DYNAMIC
Electronic Parking Brake could not be applied, car may be free rolling
Non-nominal termination of external park
Motor current was higher than expected.
Motor current measurement, with calibration offset subtracted, was higher than 17 amps.
Voltage drop on input power is high
Electronic Parking Brake is performing dynamic apply
One or more of the expected CAN messages from TAS were not received.
A message the local ECU expects to receive from the TAS ECU hasn't been received within the expected timeout or the drop rate is too high while the TAS is CAN active. The ECU is considered CAN active when VCFRONT_vehGoToSleep is 0.
All messages the local ECU expects to receive from the TAS ECU are being received or the TAS ECU is CAN inactive.
Air suspension functionality may be missing.
VCLEFT/VCRIGHT: Estimated resistance exceeds 500mOhm when input current is under 15A and exceeds 50mOhm when input current is over 15A. (VC-6540); VCFRONT: Estimated resistance exceeds 100mOhm when input current from PCS is under 10A and exceeds 20mOhm when input current is over 10A.
VCLEFT/VCRIGHT: Estimated resistance is less than 500mOhm when input current is under 15A and is less than 50mOhm when input current is over 15A. (VC-6540); VCFRONT: Estimated resistance is less than 100mOhm when input current from PCS is under 10A and is less than 20mOhm when input current is over 10A.
May result in vehicle becoming inoperable. Note: Service should ignore this alert on VCFRONT for the time being.
Road grade is too steep to secure with Park Brake
Car is parked on a road grade too steep to park; car parked on grade >30% or car with brembo Electronic Parking Brake parked on grade >27% and temperature less than -25degC
Electronic Parking Brake not parked
Car may not be secured by Electronic Parking Brake on the current road grade, may be free rolling
One or more of the expected CAN messages required from DI when not in drive mode were not received.
Przepisz go dokładnie, razem z literą i numerem. Najpewniej jest zrobić zdjęcie ekranu — kody często różnią się jedną cyfrą, a pomyłka prowadzi zupełnie gdzie indziej.
Część kodów znika po restarcie ekranu albo po kilku godzinach postoju zamkniętego auta. Jeśli kod nie wraca, zwykle był to jednorazowy zanik.
Jednorazowy wpis i kod pojawiający się po każdej jeździe to dwie różne sprawy. Serwisowi bardzo pomaga wiedza, kiedy dokładnie się pojawia.
Przy poduszkach, hamulcach, układzie kierowniczym i wysokim napięciu czekanie nie ma sensu. Przy pozostałych grupach można poczekać i zobaczyć, czy kod w ogóle wróci.
Kody błędów to tylko część obrazu. Przy autach na TesLiście widzisz dodatkowo stan baterii pobrany prosto z samochodu i kalkulator ceny, który z aktualnej oferty wylicza, ile dane auto naprawdę dziś kosztuje.