Kod TAS_a073 zgłosił w aucie sterownik „Zawieszenie pneumatyczne”. Litera „a” w środku kodu zalicza go do wpisów typu alert.
Tesla Air Suspension — zawieszenie pneumatyczne: sprężarka, zawory, czujniki wysokości. Kody objawiają się tym, że auto nie potrafi podnieść ani wypoziomować nadwozia albo zgłasza spadek ciśnienia. W Modelu S i X to z wiekiem częsta usterka.
Najczęstszy typ. Auto zapisało zdarzenie i mogło je pokazać na ekranie. Skala jest szeroka — od drobiazgu, który znika sam, po sprawę wymagającą naprawy.
Tak błąd nazywa się bezpośrednio w firmware auta. Przy kodach bez opisu to najdokładniejsza istniejąca wskazówka — sama nazwa mówi, czego dotyczy zdarzenie.
Poniższy tekst pochodzi z dokumentacji technicznej Tesli i zostawiamy go w oryginalnym angielskim brzmieniu, żeby tłumaczenie nie zmieniło znaczenia.
On board 5V switched supply is measured to be below 4.5V.
Air suspension leveling will be disabled. Systems with adaptive dampers will no longer drive current to dampers.
Debug information for 10ms task errors. Set along with TaskSchedulerError.
Rear left height sensor disconnected, or signal line from rear left PWM height sensor floating.
Expected PWM signal received from rear left ride height sensor.
Failure of a software assertion.
Auto clears after 10ms of no new assertions.
Reservoir air valve has reached its duty cycle (on time) limit.
Reservoir air valve has dropped below its duty cycle (on time) limit, plus some hysteresis.
Air suspension leveling will be temporarily disabled until reservoir air valve duty cycle drops.
Rear right height sensor disconnected, or signal line from rear right PWM height sensor floating.
Indicates an active connection to the XCP state machine
Exhaust air valve has reached its duty cycle (on time) limit.
Exhaust air valve has dropped below its duty cycle (on time) limit, plus some hysteresis.
Air suspension leveling will be temporarily disabled until exhaust air valve duty cycle drops.
Front axle has been measured to be higher than any reasonable height.
Front axle has been measured to be higher than any reasonable height for an extended period.
Front axle has been measured to be not be higher than any reasonable height for an extended period.
Vehicle may fail to level to correct ride height.
Air suspension failed to adjust to target ride height.
Vehicle may not be at correct ride height.
Reservoir air valve detected open circuit.
Reservoir air valve commanded on but no electrical current measured.
Boost air valve detected open circuit.
Boost air valve commanded on but no electrical current measured.
Air suspension raising will only occur via reservoir or air compressor.
Static vehicle spring leak check detected a spring leak on the front right air spring.
Front right air spring leak was detected with vehicle static.
Sleep cycle, or successful static spring leak check.
Reset can be caused by: Clock Error, Flash Error, Software Reset, Checkstop Reset, Debug Reset
One or more CAN messages from CP are not being received by the ECU.
One or more CAN messages from CP are not being received by the ECU (missing, bad RX rate, or invalid checksum/counter).
Successful reception of all RXd CAN messages from CP.
Air suspension will assume the vehicle is not charging.
Air suspension system is operating under limp home mode 30 restrictions.
The ECU has detected an issue whose severity requires operating under limp home mode 30 restrictions.
Air suspension leveling will be disabled, expect lowering to STANDARD via speed based restrictions on higher heights.
Static vehicle spring leak check detected a spring leak on the front left air spring.
Front left air spring leak was detected with vehicle static.
Signal line from rear left PWM height sensor shorted to ground.
Implausible condition detected on boost air valve circuit.
Implausible condition detected on boost air valve circuit, possibly due to ECU hardware failure.
ECU has requested suspension red warning lamp to be displayed.
ECU has requested suspension red warning lamp to not be displayed.
Red suspension warning lamp will be displayed.
Przepisz go dokładnie, razem z literą i numerem. Najpewniej jest zrobić zdjęcie ekranu — kody często różnią się jedną cyfrą, a pomyłka prowadzi zupełnie gdzie indziej.
Część kodów znika po restarcie ekranu albo po kilku godzinach postoju zamkniętego auta. Jeśli kod nie wraca, zwykle był to jednorazowy zanik.
Jednorazowy wpis i kod pojawiający się po każdej jeździe to dwie różne sprawy. Serwisowi bardzo pomaga wiedza, kiedy dokładnie się pojawia.
Przy poduszkach, hamulcach, układzie kierowniczym i wysokim napięciu czekanie nie ma sensu. Przy pozostałych grupach można poczekać i zobaczyć, czy kod w ogóle wróci.
Kody błędów to tylko część obrazu. Przy autach na TesLiście widzisz dodatkowo stan baterii pobrany prosto z samochodu i kalkulator ceny, który z aktualnej oferty wylicza, ile dane auto naprawdę dziś kosztuje.